The pur water filter has become one of the most popular water filters due to its unmatched ability to remove impurities from the water that is up to 99% pure.
While it has been praised by many people as the best water filter available today, there have also been a lot of complaints about how some of these pur water filters don’t work as they should.
This guide will show you how to troubleshoot these water filters if they aren’t working as they should and what to do if they start acting up.
The Pur Water Filter Troubleshooting Guide is a step-by-step, problem-solving guide for troubleshooting and repairing Pur Water filters and other Pur water systems.
The Pur Water Filter Troubleshooting Guide provides the information you need to effectively repair and troubleshoot any of the more common issues with Pur Water Filters. The troubleshooting guides are extremely helpful when your water filter is not producing the correct amount of water.
Why You Need a Pur Water Filter
A pur water filter removes all bacteria from your water. This is important because many people are unaware of the extent of the danger that is associated with bacterial contamination.
A pur water filter will help eliminate the chances of being poisoned. A pur water filter also helps keep the environment clean because bacteria can cause severe health problems if it contaminates water sources.
People can have different reasons why they buy pur filters. They may be concerned about the quality of water in their homes. They may be looking for a pur filter because of its long-lasting qualities.
Many people use a pur filter in their homes because they want to enjoy clean, pure, and healthy water. Pur filters come in different sizes and shapes, and some even come with different filters for different purposes.
Many different filters available are specially designed for home or business purposes. You can get a pur filter with different water-purifying elements that you can add.
The more filtration elements you add, your pur filter will work better. The filters have different levels of efficiency, so you need to choose the right one for your needs.
How to Fix Problems Installed by Others
First of all, the product needs to be installed correctly and professionally. Next, the seller must ensure that the filter is adequate, reliable, and up to clean the water for human consumption.
The third requirement is that the seller educates customers about how to use the product properly and how to maintain the equipment. Finally, the seller must ensure that they offer ongoing technical support and warranty service when the equipment is used as intended.
Fix the air.
According to Consumer Reports, the Pur filters are the number one selling brand of air purifiers in the United States today.
The company has grown throughout the years. It has gone from being a one-man operation to a massive global enterprise with over 1,000 employees and sales of over one million units in the United States. In the past few years, he has been alone.
Fix the filter.
To save you time and energy, I’ll walk you through the process of cleaning a Pur water filter. Remove the filter from the tank after turning off the water. Remove the two screws at the back of the filter, and lift them out of the tank.
A small rubber gasket should be under the filter, which needs to be removed. The gasket can be pry up with a screwdriver by using the flat end. The filter will need to be cleaned by soaking in a large bowl of distilled water (or any other non-toxic solution).
You can also use a small bottle of distilled vinegar or lemon juice. Let the filter soak in the solution for about 30 minutes. It now needs to soak for one more hour before it can be used again.
Fix the system.
If you’re having problems with your pur water filter, the first step to fixing the system is determining which system component is causing your problem. The first thing to try is a troubleshooting step to find out what the issue is. You can start by checking each component listed in the troubleshooting guide below.
To make a PUR filter system in a DIY kit, start with the base and fill it up with a solution of water, vinegar, and baking soda. This can be done in any spray bottle that comfortably fits your wrist.
Then, in the neck of the bottle, place a piece of mesh to catch sediment that may build up. When the solution is ready to use, pour it down the throat of the filter. After a few minutes, the filter should be full of the clean solution. Then, throw it out.
Clean the filter.
To ensure the filter is working effectively, you should be able to see some water through the filter. If it’s clear, that’s a good sign that it’s working properly. If there’s too much water coming out of the spout, it might mean your filter is clogged.
In this case, you’ll need to clean it. To do this, rinse the filter with tap water until all the dirt comes out. Then, let it dry completely before putting it back into the tank.
Clean the tank.
- A pur water filter is pretty easy to maintain and use. The only tricky part is cleaning the tank once it gets full, which can be confusing. But here’s how to do it:
- Turn off the pump and wait for the water to stop flowing.
- Remove the top half of the filter, and then tilt the bottom half back to let the sediment fall out.
- Scrub down the sides of the tank with a wet sponge, and rinse out any remaining sediment.
- Place the top half back on and press firmly to squeeze the sediment out of the filter.
- Wait a few minutes for the sediment to settle, and then turn the pump on again.
Fix the leaks
To fix the leaky water filter, you will need a good quality wrench and some new gaskets. Remove the old gaskets by prying them off with a screwdriver or the side of a hammer, and replace them with the new ones. Wrench in hand, carefully tighten the screws, so the gasket does not become distorted.
Check Your Water
Before using a PUR filter, it is essential to check the quality of your water. By using a home test kit, you can ensure that you are drinking clean, safe drinking water. Ask your local health department if you don’t know where to get a test kit. They usually offer free tests every month.
Maintain Your Water Filter
Once you’ve used your PUR filter for a while, you’ll want to maintain it regularly. Your filter should be changed once a year in order to keep your system functioning smoothly. Also, remember to take care when storing your filter. Keep it somewhere cool and dark, preferably in a sealed container.
Contact Customer Service
Contact customer service if you’re still experiencing issues after following these steps. They can help you figure out how to fix your PUR filter.
How to Replace Your Pur Water Filter
Once you’ve replaced the gaskets, you’re ready to install the new filter. To do this, follow these steps:
- Unscrew the screws holding the filter in place.
- Lift the filter out of the tank.
- Carefully set the filter in the tank. Make sure the holes align with the corresponding holes in the tank.
- Screw the screws back in.
- Fill the tank with water until the water level reaches the top of the tank.
- Close the lid and watch as the water fills the tank. Once the water has reached the top, close the lid and enjoy!
- Check the filter.
After replacing the filter, check the water flow rate through the filter. It should be around 1 liter per minute. You may have to adjust your PUR water filter settings if it’s lower than this.
Pur Water Filter Troubleshooting: Causes and solutions
1. Headache: What does this sound like? It’s probably a clogged filter.
2. Bloating could be due to something as simple as a bad pump.
3. Bad Taste: A dirty pump could also mean too dirty for the filtration system to handle properly.
4. Stuffy Nose: Another thing to check is your pump’s filter, which you can remove easily by turning the water faucet on.
5. Burning Feet: There are some more serious issues with your pump that may require a replacement, but for the rest, try unplugging your pump, then take a quick bath with your hands to see if that helps.
6. Sore Throat: If that doesn’t work, you’ll need to contact a professional who can help diagnose the problem and replace the pump.
7. Tummy Trouble: Did you know that there are two pumps? The other is for the bathroom!
8. Sore Head: If this happens when you’re not wearing a hat, it could be a sign that you’ve got an under-wiring issue.
9. Spitting Up: You might have a blockage in your pump.
10. Swollen Face: This could be a sign that your pump needs maintenance.
11. Dry Mouth: A dirty pump could cause this, too.
12. Chapped Lips: It could also be a sign that your filter needs cleaning.
13. Coughing: If you notice that your cough gets worse when you drink from the tap, it could be because your water is contaminated.
14. Runny Noses: This could be a symptom of a blocked pipe.
15. Running nose: If you notice a runny nose when you use the tap, it could mean your pipes are leaking.
What Is the Problem with My PUR Water Filter Light?
If your PUR tap water filter light isn’t working, it could be in sleep mode. When you perform a filter change, press and hold the reset button for 5 seconds in this case.
How to solve a PUR water filter blinking red after changing the filter?
If you need to replace a filter with a new one, you will see the filter light flash red on the device.
It could indicate that there is debris inside your filter if your filter light is still blinking red even after you have replaced the filter. It is recommended that you clean out the casing and try again.
Here’s how to set up a PUR water filter.
Several types of pitcher filters and faucet filtration systems operate differently. Follow these directions for installing the PUR water filter.
How to reset the PUR water filter
To take full advantage of your filter, the indicator light on the filter must be functioning. The light may not automatically turn green when a replacement or installation occurs. To get it to turn green again, follow these steps.
Why is my PUR faucet filter so slow
A slow PUR faucet filter can be caused by being blocked with air, having a lot of debris in the water, having hot water damage, having hard water damage, being incorrectly installed, or an old filter. A slow faucet filter can be resolved by following these steps.
The faucet filter is prone to developing air bubbles. The filter must be removed from the faucet mount and placed in a glass jar bigger than the filter. Let it soak for about 15 minutes after the glass is filled with water.
Tap the filter gently against the side of the sink after removing the filter from the glass jar. It takes 20-30 seconds to hold the filter upright, reinstall it on the faucet mount, and turn on the water.
A poorly installed filter will slow the filtration process and leak. Replace the faucet filter with a new one, realign the threads, and tighten it until it clicks into place.
When there are obstructions in the threading of the filter housing, the device will filter slowly. Take special care along the threads of the filter housing when cleaning it.
Due to fewer open pores, a clogged filter will filter water slowly. Gradually, filtration speed will slow down over time, but if it occurs suddenly, sediments in your water supply have suddenly increased. Check your filter or replace it by disconnecting it and cleaning it.
It is possible to have the filter flow too fast or too slow due to hot water damage. If the filter becomes damaged, it cannot be repaired.
You won’t be able to filter properly if you don’t flush a new filter properly. The filter sieve will be blocked by debris and sediments during the manufacturing and delivery of the filter. To flush it, you need to run cold water through the faucet filter for about five minutes.
Hard water will clog the pores in the filter with the scale from mineral damage, thus causing the filtration process to move slowly. The PUR water filter does not filter hard water minerals (magnesium and calcium). If you live in that region, hard water will require you to change your filter more frequently.
Those with high or low water pressure will find their filters are less effective. Water is forced through a filter by the water pressure from the faucet. Open the faucet all the way. When the water pressure is high, air bubbles will block the flow. The filter needs to be soaked for 15 minutes in cold water and washed with cold water for about 30 seconds.
What are some ways to clean a clogged PUR water filter?
For the water filter to function effectively, sediments and debris must be removed, and the filter pores can also become clogged with mold and bacteria. To prevent this dirt from entering your water, you need to unclog your filter periodically. To do so, please follow these steps.
To loosen dirt from the filter, you should soak the water filter in water for between five and eight minutes.
Using a mixture of water, mild dishwashing soap, and vinegar, wash the dispenser and the opening passage and wipe everything clean with a soft cloth. It should be disinfected by the mild dishwashing soap and vinegar mixture.
Rinse thoroughly to ensure no soap residue on the filter components.
Install the faucet filter as instructed.
How to replace the batteries on a PUR water filter
Electronic filters powered by batteries are available in the PUR water filter line. Generally, the batteries should last quite a while, but you may need to change them periodically depending on how frequently you use them. Underneath the sink is a battery chamber with an indicator light that flashes red when it needs to be replaced. You can return your PUR electronic water filter batteries by following the steps below.
Put the battery chamber directly above the filter head, underneath the sink.
Remove the two AA batteries from the battery compartment.
Ensure the negative (-) and positive (+) charges are aligned when installing the new batteries.
Insert the battery compartment back into its slot until you hear a clicking sound. After about 10 seconds, the indicator light turns solid green, indicating the battery is working properly.
How can I fix the light on the pur water filter?
If your PUR water filter is idle, its indicator lights won’t work. When the light flashes green and functions correctly, you need to reset it.
This indicates that the filter is functioning properly. Even though the filter is working, the indicator light will eventually stop working because it has a non-replaceable battery.
As you will never know whether or not the filter needs replacing or if it is working properly, it is best to replace the whole system.
Why does my PUR filter blink red after I replace the filter?
Why is my traffic light flashing red when I replace the filter? Wouldn’t it mean I should start driving again when the green light appears?
When the red blink appears on a PUR filter, it indicates the filter has quit filtering water and needs to be changed. A faulty installation or a damaged PUR filter possibly caused the issue if you just installed a new PUR filter.
You can interpret this blinking as a sign that your existing PUR filter has already filtered 100 gallons of water and should be replaced.
What are the indications that PUR water filters are working correctly?
Changing your PUR water filter cartridges regularly is important. But why?
You might be getting contaminated or impure water from your filter if it isn’t working correctly. The older filter must be replaced to get clean, safe water.
To determine whether the purifier works properly, you have to identify when the purifier needs to be changed quickly.
The following are some common signs:
It’s time to replace the PUR filter if a red light blinks on the panel bar.
If the pH goes out of the normal range of 6.5 to 7.5, the filter should be changed.
In addition, the conductivity and TDS should be checked, and they must be changed if it is out of range.
Filters and pre-filters that are not functioning properly are commonly identified by bad smells, sediment accumulation, and slow filtration.
The water dispenser may have a filtration problem if it clogs often or provides weak water flow.
How can I fix PUR water dispenser drainage problems?
A PUR dispenser may show slow draining if liquid bubbles form a thin film on the filter unit or clog the unit with volatile substances.
This issue can be resolved simply by slowly removing the filter and banging it against a solid surface. Be careful not to damage the inner settings of the unit by hitting too hard.
Once the filter is installed on the unit, shake it vigorously.
How can I make my PUR water filter smell better?
If raw water contains excessive hydrogen sulfide, this problem is common. Organic molecules can also accumulate on the filter mesh if the raw water contains excessive hydrogen sulfide.
It is possible to soak the filter in a solution of organic disinfectants to remove the contaminants. One lemon can be juiced into two liters of water, or you can add two tablespoons of white vinegar to the water.
Reinstall the PUR filter after it has dried. Soak the PUR filter in the bowl for a few minutes.
Pur Water Filter Troubleshooting Guide How to Unclog a PUR Water Filter (Slow Drain Fix):
Conclusion
In conclusion, the water filter has been used by millions of people across the globe for decades and is a must-have tool. Unfortunately, not all filters are created equal. The more expensive and technologically advanced filters work better than cheaper filters advertised with pretty pictures.
But even those that claim to be more effective than other brands may still be causing issues. Some common reasons for filter issues include a bad filter cartridge, bad water chemistry (especially if it’s hard water), or a bad connection to the filter itself. Here is a guide to troubleshooting the most common problems with your Pur filter.
For those who are not sure how to troubleshoot a Pur Water Filter, the video will show you step by step.
Sarah J. Gregory
352 Hershell Hollow Road
Anaheim, CA 92805
